Huawei V100R006C00 Configuration Manual Download Page 104

Page: 104 / 142

rule

A basic or an advanced ACL rule is created.

For details on the

rule

command, see the

Quidway S5700 Series Ethernet Switches - Command

Reference

----End

7.15.3 Configuring an Observing Port

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

observe-port

index

interface

interface-type interface-number

A global observing port is configured.

----End

7.15.4 Configuring CPU Mirroring

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

port-mirroring cpu

[

acl

acl-number

]

to observe-port

index

inbound

CPU mirroring is configured.

By default, CPU mirroring is disabled.

----End

7.15.5 Checking the Configuration

Run the following commands to check the previous configuration.

Action

Command

Check information about port
mirroring.

display port-mirroring

Check information about CPU
mirroring.

display cpu port-mirroring

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Summary of Contents for V100R006C00















































































































































Search results

Summary of Contents for V100R006C00

Reviews:

Brands by name

Popular brands

Huawei V100R006C00, Configuration Manual

Search results

Summary of Contents for V100R006C00

Reviews:

Brands by name

Popular brands