manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 31

Switch B and Switch C having an empty configuration. Switch B and Switch C need to be directly
connected via a single hop. Both the interfaces connecting Switch B and Switch C should be in
the Up state, and should support NAP.

Figure 2-2

 Networking diagram of NAP-based remote deployment

Network

SwitchA

PC

SwitchB

SwitchC

 

Configuration Roadmap

The configuration roadmap is as follows:

1.

Configure a primary IP address and a secondary IP address on Switch B.

2.

Configure a NAP master interface on Switch B.

3.

Telnet to Switch C from Switch B by means of NAP.

Data Preparation

None

Procedure

Step 1

Configuring the NAP master interface

# Do as follows on Switch B.

<Quidway>

 system-view

[Quidway]

 sysname SwitchB

[SwitchB]

 interface gigabitethernet0/0/1

[SwitchB-GigabitEthernet0/0/1]

 nap port master

Step 2

Logging in to the slave device from the master device.

# Do as follows on Switch B.

[SwitchB-GigabitEthernet0/0/1]

 nap login neighbor

Trying 10.167.253.10 ...
Press CTRL+K to abort
Connected to 10.167.253.10 ...

Info: The max number of VTY users is 10, and the number
      of current VTY users on line is 1.

Step 3

Shutting down NAP on the slave device.

# Do as follows on Switch C.

<Quidway>

 system-view

[Quidway]

 sysname SwitchC

[SwitchC]

 undo nap slave enable

----End

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

2 NAP Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

22

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands