manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 110

Figure 7-6

 Networking diagram of local MAC address mirroring

PC1

PC2

GE0/0/2

GE0/0/3

GE0/0/1

PC3

GE0/0/4

GE1/0/1

 

Configuration Roadmap

The configuration roadmap is as follows:

1.

Set GigabitEthernet 0/0/3 as an observing port.

2.

Configure local MAC address mirroring in the view of VLAN 10.

Data Preparation

None.

Configuration Procedure

1.

Configure VLAN 10 and then add GigabitEthernet 0/0/1, GigabitEthernet 0/0/2, and
GigabitEthernet 0/0/4 to VLAN 10. The configuration procedure is not mentioned here.

2.

# Set GigabitEthernet 0/0/3 as an observing port.

<Switch> 

system-view

[Switch] 

observing-port 1 interface GigabitEthernet 0/0/3

3.

Configure a mirroring MAC.
# Configure local MAC address mirroring in the view of VLAN 10.

[Switch] 

VLAN 10

[Switch-VLAN10] 

mac-mirroring 0001-0001-0001 to observe-port 1 inbound

[Switch-VLAN10] 

quit

4.

Verify the configuration.
# Run the 

display port-mirroring

 command. You can view the configuration of the

observing port.

[Switch] 

display port-mirroring

 Observe index 1 is set to interface GigabitEthernet0/0/3
   Observe Type: Local
 Observe index 2 is not set to any interface
 Observe index 3 is not set to any interface
 Observe index 4 is not set to any interface

Configuration Files

Configuration file of the Switch

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

101

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands