manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 91

l

The number of the observing port is configured properly.

7.9 Configuring RSPAN Based on MAC Addresses

This section describes how to configure RSPAN based on MAC addresses.

7.9.1 Establishing the Configuration Task

Applicable Environment

When incoming packets with the specified source or destination MAC address in a VLAN need
to be monitored on the S5700, you can configure RSPAN based on MAC addresses if the
monitoring interface receiving these incoming packets is not located on the same S5700 as the
observing port.

Pre-configuration Tasks

None.

Data Preparation

To configure RSPAN based on MAC addresses, you need the following data.

No.

Data

1

Type and number of an observing port

2

MAC address of the packet to be mirrored

3

ID of the VLAN that the packet with the MAC address to be mirrored belongs to

4

ID of an RSPAN VLAN

 

7.9.2 Configuring Remote MAC Address Mirroring

This section describes how to configure remote MAC address mirroring.

Procedure

l

Configure remote MAC address mirroring on the source switch.

NOTE

The mirrored port cannot be added to the RSPAN VLAN.

The S5700SI series do not support remote MAC address mirroring.

1.

Run:

system-view

The system view is displayed.

2.

Run:

vlan

 

vlan-id

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

82

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands