manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 118

Figure 7-9

 Networking for changing the observing port

Router

Switch

GE0/0/3

GE0/0/1

L2 Switch

Mirroring

host1

Mirroring

 host2

GE0/0/5

GE0/0/24

 

Configuration Roadmap

The configuration roadmap is as follows:

1.

Delete the mirrored port GigabitEthernet 0/0/1.

2.

Set GigabitEthernet 0/0/5 instead of GigabitEthernet 0/0/24 as the observing port.

3.

Reset GigabitEthernet 0/0/1 as a mirrored port.

Data Preparation

To complete the configuration, you need the following data:

l

Type and number of the new observing port, that is, GigabitEthernet 0/0/5

Configuration Procedure

1.

Check the configurations on the current observing port and mirrored port.
# Run the 

display port-mirroring

 command to check the configurations on the current

observing port and mirrored port.

<Switch> 

display port-mirroring

  Port-
mirror:                                                                  
----------------------------------------------------------     
  Mirror-port              Direction     Observe-port              
----------------------------------------------------------      
  GigabitEthernet0/0/1     Inbound       
GigabitEthernet0/0/24                   

2.

Delete the mirrored port.
# Delete the mirrored port GigabitEthernet 0/0/1.

<Switch> 

system-view

[Switch] 

interface GigabitEthernet 0/0/1

[Switch-GigabitEthernet0/0/1] 

undo port-mirroring inbound

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

109

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands