manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 127

8.4.1 Example for Configuring PoE on the Switch

Networking Requirements

As shown in 

Figure 8-1

, Switch supports PoE. Switch A, Switch B, and the AP can be powered

through PoE.

NOTE

Switch A, Switch B, and the AP are devices of other vendors and need to be powered through PoE.

l

Switch A is connected to GE 0/0/1 on Switch; the maximum power consumption of Switch
A is 12000 mw; Switch A is connected to the data server and needs to be powered first.

l

Switch B is connected to GE 0/0/2 on Switch; the maximum power consumption of Switch
B is 12000 mw; Switch B is connected to common users who access the Internet.

l

The AP is connected to GE 0/0/3 on Switch; the maximum power consumption of the AP
is 2500 mw; the AP is connected to users who access the Internet through a wireless
network.

Switch provides power for Switch A, Switch B, and the AP in automatic mode, and is enabled
with compatibility detection for PDs.

Figure 8-1

 Networking diagram of PoE configurations

Switch

SwitchB

SwitchA

AP

GE0/0/1

GE0/0/2

GE0/0/3

 

Configuration Roadmap

The configuration roadmap is as follows:

1.

Enable PoE on GE 0/0/1 of Switch, and configure the maximum power and the power
supply priority of GE 0/0/1.

2.

Enable PoE on GE 0/0/2 of Switch, and set the maximum power consumption of GE 0/0/2.

3.

Enable PoE on GE 0/0/3 of Switch, and set the maximum power consumption of GE 0/0/3.

4.

Configure the maximum power consumption of the interface connecting the AP on
Switch.

5.

Configure the power supply management of Switch to be in automatic mode.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

8 PoE Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

118

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands