manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 95

7.11.3 Configuring Flow Mirroring

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

observe-port

 

index

 

interface

 

interface-type interface-number

An observing port is configured.

Step 3

Run:

traffic behavior

 

behavior-name

A traffic behavior is created and the traffic behavior view is displayed.

Step 4

Run:

mirroring

 

to observe-port

 

index

Flow mirroring is configured.

----End

Follow-up Procedure

After configuring flow mirroring in a traffic behavior, you need to bind the behavior to a traffic
classifier in a traffic policy and then apply the policy to the interface. For detailed configuration
procedures, see 

7.11.4 Creating and Applying a Traffic Policy

.

7.11.4 Creating and Applying a Traffic Policy

Context

Do as follows on the S5700 that needs to be configured with flow mirroring.

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

traffic policy

 

policy-name

A traffic policy is created and the policy view is displayed.

Step 3

Run:

classifier

 

classifier-name

 

behavior

 

behavior-name

A traffic behavior is configured for a specified class in the traffic policy.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

86

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands