manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 90

No.

Data

1

Type and number of the observing port

2

MAC address of the packets to be mirrored

3

ID of the VLAN that the observed MAC address belongs to

 

7.8.2 Configuring Local SPAN Based on MAC Addresses

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

observe-port

 

index

 

interface

 

interface-type

 

interface-number

An observing port is configured.

Step 3

Run:

vlan

 

vlan-id

The VLAN view is displayed.

Step 4

Run:

mac-mirroring

 

mac-address

 

to observe-port

 

index

 

inbound

Local SPAN based on MAC addresses is configured.

You can repeatedly perform 

Step 3

 and 

Step 4

 to monitor the incoming packets with multiple

MAC addresses in multiple VLANs.

----End

7.8.3 Checking the Configuration

Run the following commands to check the previous configuration.

Action

Command

Check information about the
observing port.

display observe-port

Check information about port
mirroring.

display port-mirroring

 

If the following results are obtained, the configuration is successful:

l

The type of the observing port is configured properly.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

81

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands