manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 67

Step 4

Run:

terminal monitor

The terminal is enabled to display information.

By default, the terminal is enabled to display information.

Step 5

Run:

terminal debugging

or

terminal logging

or

terminal trapping

The terminal is enabled to display debugging information, logs, and traps.

NOTE

Step 4

 and 

Step 5

 are not listed in sequence.

----End

6.3.2 Sending Information to the Telnet Terminal

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

info-center monitor channel

 { 

channel-number

 | 

channel-name

 }

Information is sent to the Telnet terminal.

Step 3

Run:

quit

Return to the user view.

Step 4

Run:

terminal monitor

The terminal is enabled to display information.

Step 5

Run:

terminal debugging

or

terminal logging

or

terminal trapping

The terminal is enabled to display debugging information, logs, and traps.

NOTE

Step 4

 and 

Step 5

 are not listed in sequence.

----End

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

6 Monitoring the Device Through the Information Center

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

58

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands