manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 86

7.5.3 Checking the Configuration

Run the following commands to check the previous configuration.

Action

Command

Check information about the
observing port.

display observe-port

Check information about port
mirroring.

display port-mirroring

 

If the following results are obtained, the configuration is successful:

l

The type of the observing port is configured properly.

l

The number of the observing port is configured properly.

7.6 Configuring Remote VLAN Mirroring

This section describes how to configure remote VLAN mirroring.

7.6.1 Establishing the Configuration Task

Applicable Environment

When incoming packets passing through any active interfaces of the S5700 in a specified VLAN
or some VLANs need to be monitored, you can configure remote VLAN mirroring if the interface
added to the monitored VLAN is not located on the same S5700 as the observing port.

NOTE

S5700SI does not support remote VLAN mirroring.

Pre-configuration Tasks

Before configuring remote VLAN mirroring, complete the following tasks:

l

Creating a VLAN as the monitored VLAN

l

Adding physical interfaces to the monitored VLAN

Data Preparation

To configure remote VLAN mirroring, you need the following data.

No.

Data

1

Type and number of the observing port

2

ID of the mirrored VLAN

3

ID of the RSPAN VLAN

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

77

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands