manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 133

Step 3

Run:

als enable

ALS is enabled on the interface.

By default, ALS is disabled on an interface.

----End

9.3.3 (Optional) Setting the Restart Mode of the Laser

The laser can work in automatic restart mode or manual restart mode. By default, the laser works
in automatic restart mode.

Prerequisite

ALS is enabled on the interface.

Context

If the laser of an optical module works in automatic restart mode, the laser starts automatically
at ALS pulse intervals. If the laser of an optical module is set to work in manual restart mode,
you must start the laser manually. Then the laser sends a pulse.

If the fiber link recovery is detected in time, you can use the manual restart mode so that the
laser can send pulses immediately. Therefore, data communication can be recovered rapidly.

By default, the laser works in automatic restart mode after ALS is enabled on all the interfaces.

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

interface

 

interface-type interface-number

The interface view is displayed.

Step 3

Run:

als restart mode manual

The restart mode of the laser is set to manual.

The ALS pulse width of the interface in manual restart mode is the same as that in automatic
restart mode.

----End

9.3.4 (Optional) Starting the Laser Manually

When the laser works in automatic restart mode, you need to manually open the laser so that the
laser sends one pulse.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

9 ALS Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

124

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands