Huawei FusionModule1000A Installation Manual Download

Page: 88 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

11 Installation Verification

Issue 03 (2020-06-09)

Installation Verification

After the FusionModule1000 installed, verify the installation as described in

Table 11-1

Table 11-1

Installation checklist

No. Check Item

Check
Method

Expected Result

Pre-fab. module
installation

Observe

The installation conforms to the design
requirements.

Equipment
appearance

Observe



The equipment is intact and free from
inclination, distortion, pain drop, and
rust.



All connections are secure.

Water pipe
connections

Observe

Water pipes are securely connected.

Thermal insulation
layers on water pipes

Observe

All pipes are seamlessly wrapped with
thermal insulation layers.

External grounding

Observe



Each pre-fab. module has at least two
ground points and is grounded securely
with a ground resistance of 10 ohms or
less.



Each row of cable trays has at least two
ground points and is grounded securely
with a ground resistance of 10 ohms or
less.

Cable connections

Observe



All cable connections are secure,
especially network cable connections.



Bear cables and terminal barrels near
wearing terminals are wrapped in
insulation tape or heat shrink tubing.



Flat washers and spring washers of all
wiring terminals are securely installed.



Cables are routed in the way convenient
for future maintenance and expansion.

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands