Huawei FusionModule1000A Installation Manual Download Page 34

Page: 34 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

4 Installing Pre-fab. Modules

Issue 03 (2020-06-09)

4.2.3 Hoisting and Securing Pre-fab. Modules

Prerequisites

To facilitate subsequent installation, ensure that pre-fab. modules are level after hoisting.



Pre-fab. module bases have been installed and leveled.



Select an appropriate crane based on standards of the crane company, and ask a
professional to assess the crane onsite.



Twistlocks in pre-fab. module bases are in correct positions.



The hoisting ropes are available.



The doors of pre-fab. modules to be hoisted are closed.



The weather is good without wind when pre-fab. modules need to be hoisted outdoors.

Context

Ensure that the crane and steel ropes can bear the load weight.

Table 4-3

Parameters for hoisting pre-fab. modules

Weight

Steel
Rope
Length

Steel Rope
Quantity

Dimensions (H x W x D)

Net weight: <
14,000 kg

> 12.5 m

4 PCS

2896 mm x 2438 mm x 12,192 mm

Hoisting Precautions

Stage

Precautions

Before hoisting

Ensure that the crane and steel ropes provide the required bearing
capacity.

Ensure that the twistlocks in container bases are in correct positions.

Ensure that the steel ropes are securely connected.

During hoisting

Do not allow any unauthorized people to enter the hazardous areas
and never stand under the crane arm during hoisting.

Ensure that the crane is properly located and avoid long-distance
hoisting.

Keep the pre-fab. module stable and horizontal during hoisting, and
ensure that the diagonal gradient of the pre-fab. module is within 5
degrees.

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands