Huawei FusionModule1000A Installation Manual Download Page 36

Page: 36 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

4 Installing Pre-fab. Modules

Issue 03 (2020-06-09)

Figure 4-13

Tightening a twistlock in a single-capacity base

----End

Follow-up Procedure

After pre-fab. modules are hoisted and installed, verify the installation to ensure normal use of
products and smooth subsequent installation.

Table 4-4

Installation checklist

No.

Check Item

Check Method

Criteria

Bolts and nuts of
twistlocks

Partially tighten them
using a wrench.

Bolts and nuts are tightened.

Contact between
pre-fab. modules and
bases

Observe.

A pre-fab. module is in close
contact with and evenly
supported by the bases
underneath.

Pre-fab. module doors

Open and close each
pre-fab. module door
once.

All pre-fab. module doors
can be smoothly opened and
closed.

4.3 Grounding Pre-fab. Modules

Prerequisites



The pre-fab. modules have been installed.



The grounding positions have been specified.



The grounding requirements have been specified.

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands