Huawei FusionModule1000A Installation Manual Download Page 96

Page: 96 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

A A Basic Installation Operations

Issue 03 (2020-06-09)

Cables must be bound neatly, and cable ties must be secured evenly and properly in the same
direction.

----End

A.1.6 Routing Cables into Feeder Windows

DPJ end connectors and waterproof metal connectors are available on pre-fab. module feeder
windows. When routing cables through a feeder window, follow the appropriate installation
procedure.



After cables are routed into feeder windows on the ends of pre-fab. modules, use
Styrofoam to seal the hole inside the pre-fab. modules.



The armored cables must be grounded.

External cables must be routed from bottom to top and have backwater bend.

Figure A-4

Backwater bend

A.1.6.1 Installing DPJ End Connectors

Prerequisites



Do not operate a feeder window outdoors under bad weather conditions if no shelter is
available.



Cables have been mounted on cable trays.



Cables need to be routed into a feeder window using DPJ end connectors.

Except armored power cables, other external cables of the FusionModule1000 must be routed through a
feeder window using DPJ end connectors.

Context

A DPJ end connector consists of a body, ferrule, guarding, and cover lock nut, as shown in

Figure A-5

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands