Huawei FusionModule1000A Installation Manual Download

Page: 77 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

8 Installing Devices Inside Pre-fab. Modules

Issue 03 (2020-06-09)



If the ejector is not pressed down, extinguishant may be released.



The electrical actuator ejector is 11 mm long before being pressed down, and 7 mm long
after being pressed down.

Figure 8-23

Operating the electrical actuator ejector

Remove the protective cover at the electrical actuator installation position on the
container valve. Align the electrical actuator and the container valve, and tighten the
electrical actuator clockwise

----End

8.4.1.2 Connecting the Cable to the Battery of the Fire Control Panel

Prerequisites

The pre-fab. modules have been installed.

Preparations

The fire control panel battery has been installed before delivery. You only need to connect the
reserved cable to the battery onsite.

Tools: protective gloves

Materials: none

Skill requirement: common technician

Procedure

Step 1

Open the door of the fire control panel.

Step 2

Remove the protective foam from the battery and check whether the battery is intact or leaks.

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands