Huawei CX600-X1-M Series Hardware Description Download Page 96

Page: 96 / 234

Table 3-29

Attributes of the AUX interface

Attribute

Description

Connector type

RJ45

Working mode

Duplex UART

Electrical
characteristics

RS-232

Baud rate

The default value is 9600 bit/s. The value can be configured.

Data equipment
type

DTE (Data Terminal Equipment)

Cable
specification

8-core shielded cable

Table 3-30

lists the external clock interface attributes.

Table 3-30

Attributes of the external clock interface

Attribute

Description

Connector type

RJ45

Cable
specification

120-ohm clock shielded cable

Standard
compliance

G.703

Specifications

Table 3-31

lists the specifications of the MPUK.

Table 3-31

Specifications of the MPUK

Item

Specification

Silkscreen of the board
name

CX-MPUK

Typical power
consumption

20 W

Heat dissipation

64.9 BTU/hour

Weight

0.6 kg ( 1.32 lb )

Dimensions (H x W x D)

20 mm x 194 mm x 226 mm (0.79 in. x 7.64 in. x 8.90 in. )

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

3 CX600-X2-M16 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands