Huawei CX600-X1-M Series Hardware Description Download Page 26

Page: 26 / 234

Figure 1-12

Data plane architecture of the CX600-X1-M4

OVER

SUBSCRI

BED

NPU

H
Y

SFP

RJ45

INTERFACE

CONVERSION

MODULE

H
Y

SFP

RJ45

INTERFACE

CONVERSION

MODULE

1.4.2 Introduction to the NPU-50

NOTE

NPU-50 must not be installed in an outdoor cabinet.

The NPU-50 on the CX600-X1-M4 processes service data of the entire system.

The NPU-50 has a 50-Gbit/s forwarding capability in each direction, and all subcards exchange
data through the NPU-50.

You can install only one NPU-50 on the chassis of the CX600-X1-M4.

The NPU-50 consists of the following planes:

Control and management plane

Through the management channels between MPUs and the NPU-50, the MPUs can manage
the subcards, and transmit routing protocol data.

Data forwarding plane

The NPU-50 is responsible for service processing in the entire system, and is connected to
all subcards through data channels.

Table 1-11

NPU-50 parameters

Item

Description

Remarks

Forwarding capability

50 Gbit/s (bidirectional)

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

1 CX600-X1-M4 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands