Huawei CX600-X1-M Series Hardware Description Download Page 85

Page: 85 / 234

3.4 Data Plane

3.4.1 Introduction to the Data Plane

NPUs are key parts on the CX600-X2-M16 and are responsible for network processing and data
exchange between PICs and NPUs.

The procedure for data processing is as follows:

The IP packets sent from PICs and NPU converge at a convergence module.

The NP processes the IP packets.

The TM module performs traffic management on the IP packets.

Figure 3-11

Data plane architecture of the CX600-X2-M16

H
Y

SFP

RJ45

INTERFACE

CONVERSION

MODULE

H
Y

SFP

RJ45

INTERFACE

CONVERSION

MODULE

OVER

SUBSCRI

BED

NPU

OVER

SUBSCRI

BED

NPU

3.4.2 Introduction to the NPU-50

NOTE

NPU-50 must not be installed in an outdoor cabinet.

The NPU-50 has a 50-Gbit/s forwarding capability in each direction, and all subcards exchange
data through the NPU-50.

You can install two NPUs on the chassis of the CX600-X2-M16. The two NPUs can work in 1
+1 or 1:1 mode. In 1+1 mode, the NPU-50 is connected to the eight PICs. In 1:1 mode, the
NPU-120-E is connected to the sixteen PICs.

The NPU-50 consists of the following planes:

Control and management plane

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

3 CX600-X2-M16 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands