Huawei CX600-X1-M Series Hardware Description Download Page 60 | Manualshive

Page: 60 / 234

background image

l

Data forwarding plane
The NPUs are responsible for service processing in the entire system, and are connected
to all subcards through data channels.

Table 2-15

NPU parameters

Item

Description

Remarks

Forwarding capability

50 Gbit/s

-

Figure 2-17

Appearance of the NPU panel

1. STAT indicator

2. ACT indicator

3. OFL button

describes the buttons and indicators on the NPU panel.

Table 2-16

Description of the buttons and indicators on the NPU panel

Indicator/
Button

Description

STAT
indicator

If the indicator is on, the NPU is working properly.
If the indicator blinks green, NPU is being registered.
If the indicator is off, the NPU is faulty, not powered on, or fails to be registered.

ACT
indicator

If the indicator is steady green, the NPU is in the master state.
If the indicator is off, the NPU is in the slave state or fails to be registered.

OFL
indicator

If the indicator is steady red, the NPU is powered off and can be safely removed.
If the indicator is off, the NPU is working properly.

OFL
button

This button indicates the removal of the NPU. Before removing the NPU, press
and hold the OFL button for 6s until the OFL indicator comes on. Then, you
can remove the NPU.

2.4.4 Introduction to the NPU-120

NOTE

NPU-120 must not be installed in an outdoor cabinet.

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

2 CX600-X2-M8 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

50

«
...
58
59
60
61
62
...
»

Summary of Contents for CX600-X1-M Series











































































































































































































































Reviews:

No comments

Related manuals for CX600-X1-M Series

Brand: D-Link Pages: 11

Brand: D-Link Pages: 83

Brand: D-Link Pages: 129

Brand: D-Link Pages: 10

Brand: D-Link Pages: 21

Brand: D-Link Pages: 6

Brand: D-Link Pages: 17

Brand: D-Link Pages: 4

Brand: D-Link Pages: 6

Brand: D-Link Pages: 86

Brand: D-Link Pages: 3

Brand: D-Link Pages: 4

Brand: D-Link Pages: 4

DSL-3580L Series

Brand: D-Link Pages: 20

Brand: D-Link Pages: 64

Brand: D-Link Pages: 73

TokenLink Velocity 3C319

Brand: 3Com Pages: 2

ARM Cortex-A9 MPCore

Brand: Dave Embedded Systems Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands