Huawei CX600-X1-M Series Hardware Description Download Page 15

Page: 15 / 234

Table 1-1

Number and layout of slots on the CX600-X1-M4

Slot No.

Quanti
ty

Remarks

1,2, 3, and 4

For sub-cards.

For NPUs.

6 and 7

For MPUs, which work in 1:1 backup.

8 and 9

For PSUs, which work in 1+1 backup mode.

For a fan module.

Numbering Rule of Service Interfaces on the CX600-X1-M4

Service interfaces on the CX600-X1-M4 are numbered in the following format: 0/subcard slot
number/interface number on the subcard.

A subcard slot number is the number of the slot where an interface's subcard resides. A
subcard slot number ranges from 1 to 4.

An interface number on the subcard starts with 0, and its maximum value is determined by
the actual number of interfaces on the subcard.

The following figure shows how a service interface is numbered on the CX600-X1-M4.

Figure 1-5

Numbering rule of service interfaces on the CX600-X1-M4

g0/4/1

g0/1/2

Table 1-2

CX600-X1-M4 slot description

Slot

Quanti
ty

Remarks

1, 2, 3, and 4

Slots for high-speed and low-speed subcards

Slot for the NPU

6 and 7

Slots for MPUs in 1:1 backup mode

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

1 CX600-X1-M4 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands