Huawei CX600-X1-M Series Hardware Description Download Page 186

Page: 186 / 234

Attributes

Description

Maximum
transmitting
power

-14.0 dBm

-8.0 dBm

0 dBm

Receiving
sensitivity

-30.0 dBm

-31.0 dBm

-37.0 dBm

Overload
power

-14.0 dBm

-8.0 dBm

-10.0 dBm

Optical fiber
type

Multi-mode

Single-mode

C.6 E1 Interface Attributes

Table C-11

lists E1 interface attributes.

Table C-11

E1 interface attributes

Attribute

Description

Connector type

Anea96

Nominal bit rate
(kbit/s)

2048

Interface
impedance

75-ohm with coaxial cable.

120-ohm with twisted-pair cable.

Interface code

HDB3

Pulse waveform of
the output
interface

Compliant with ITU-T G.703

Attenuation (dB)
of the input
interface at a point
with the frequency
of 1024 kHz

0 to 6

Immunity of the
input interface

Compliant with ITU-T G.703

Input jitter
tolerance

Compliant with ITU-T G.823

Output jitter

Compliant with ITU-T G.823

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

C List of Interface Attributes

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

176

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands