Huawei CX600-X1-M Series Hardware Description Download Page 28

Page: 28 / 234

1.4.3 Introduction to the NPU-50-E

NOTE

NPU-50-E can be installed in an outdoor cabinet.

The NPU-50-E on the CX600-X1-M4 processes service data of the entire system.

The NPU-50-E has the 50-Gbit/s forwarding capability in each direction, and all subcards
exchange data through the NPU-50-E.

You can install only one NPU-50-E on the chassis of the CX600-X1-M4.

The NPU-50-E consists of the following planes:

Control and management plane

Through the management channels between MPUs and the NPU-50-E, the MPUs can
manage the subcards, and transmit routing protocol data.

Data forwarding plane

The NPU-50-E is responsible for service processing in the entire system, and is connected
to all subcards through data channels.

Table 1-14

NPU-50-E parameters

Item

Description

Remarks

Forwarding capability

50 Gbit/s (bidirectional)

Figure 1-14

Appearance of the NPU on the CX600-X1-M4

1. STAT indicator

2. ACT indicator

3. OFL button

Table 1-15

describes the buttons and indicators on the NPU panel.

Table 1-15

Description of the buttons and indicators on the NPU panel

Indicator/
Button

Description

STAT
indicator

If the indicator is on, the NPU is working properly.
If the indicator blinks green, theNPU is being registered.
If the indicator is off, the NPU is faulty, not powered on, or fails to be registered.

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

1 CX600-X1-M4 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands