Huawei CX600-X1-M Series Hardware Description Download Page 95

Page: 95 / 234

Interface
Name

Interface Type

Description

CLK clock
interface

RJ45

One RJ45 interfaces. It is used to input one
channel or output one channel 2-Mbit/s clock
signals, or one channel 2-MHz clock signals.

RS485 interface RJ45

Used to connect to the monitoring interface
on the external AC power supply module

Attributes of the interfaces on the MPU

Table 3-27

lists the 10Base-T/100Base-TX/1000Base-T-RJ45 interface attributes.

Table 3-27

Attributes of the 10Base-T/100Base-TX/1000Base-T-RJ45 interface

Attribute

Description

Connector type

RJ45

Working mode

Half-duplex or full-duplex mode

Standard
compliance

IEEE 802.3-2002

Cable
specification

Super category 5 Shielded Twisted Pair (STP) cables recommended in
the case of 1000 Mbit/s

Table 3-28

lists the console interface attributes.

Table 3-28

Attributes of the console interface

Attribute

Description

Connector type

RJ45

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Electrical
characteristics

RS-232

Baud rate

The default value is 9600 bit/s. The value can be configured.

Data equipment
type

Data Circuit-terminating Equipment (DCE)

Cable
specification

8-core shielded cable

Table 3-29

lists the AUX interface attributes.

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

3 CX600-X2-M16 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands