HP photosmart 850 Page 75 Command Reference Manual Download

Page: 75 / 136

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Usage guidelines

If you do not specify the

bridge-aggregation

keyword, the command displays information about all

interfaces.
If you specify the

bridge-aggregation

keyword and do not specify an interface number, the command

displays information about all aggregate interfaces.
If you specify the

bridge-aggregation

interface-number

option, the command displays information about

the specified Layer 2 aggregate interface.

Examples

# Display information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1

Bridge-Aggregation1 current state: DOWN

IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 3ce5-a6cf-e383

Description: Bridge-Aggregation1 Interface

Unknown-speed mode, unknown-duplex mode

Link speed type is autonegotiation, link duplex type is autonegotiation

PVID: 1

Port link-type: access

Tagged VLAN ID : none

Untagged VLAN ID : 1

Port priority: 0

Last clearing of counters: Never

# Display brief information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1 brief

The brief information of interface(s) under bridge mode:

Link: ADM - administratively down; Stby - standby

Speed or Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface Link Speed Duplex Type PVID Description

BAGG1 DOWN auto A A 1

# Display information about all Layer 2 aggregate interfaces in Down state.

<Sysname> display interface bridge-aggregation brief down

The brief information of interface(s) under bridge mode:

Link: ADM - administratively down; Stby - standby

Interface Link Cause

BAGG1 DOWN Not connected

Summary of Contents for photosmart 850









































































































































Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands

HP photosmart 850, Command Reference Manual

Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands