HP photosmart 850 Command Reference Manual Download Page 54

Page: 54 / 136

•

If the system fails to apply the configuration to the aggregate interface, it stops applying the

configuration to aggregation member ports.

•

If the system fails to apply the configuration to an aggregation member port, it skips the port and
moves to the next member port.

Examples

# Configure WLAN-ESS 1 as a hybrid port to forward packets from VLAN 2, VLAN 4, and VLAN 50

through VLAN 100 tagged.

<Sysname> system-view

[Sysname] interface WLAN-ESS1

[Sysname-WLAN-ESS1] port link-type hybrid

[Sysname-WLAN-ESS1] port hybrid vlan 2 4 50 to 100 tagged

# Configure ports in port group 2 as hybrid ports to forward packets from VLAN 2 untagged.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] quit

[Sysname] port-group manual 2

[Sysname-port-group-manual-2] group-member Ten-GigabitEthernet1/0/1 to

Ten-GigabitEthernet1/0/2

[Sysname-port-group-manual-2] port link-type hybrid

[Sysname-port-group-manual-2] port hybrid vlan 2 untagged

Configuring Ten-GigabitEthernet1/0/1... Done.

Configuring Ten-GigabitEthernet1/0/2... Done.

# Configure Layer 2 aggregate interface Bridge-Aggregation 1 and its member ports as hybrid ports to
forward packets from VLAN 2 untagged.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port link-type hybrid

[Sysname-Bridge-Aggregation1] port hybrid vlan 2 untagged

Please wait... Done.

Configuring Ten-GigabitEthernet1/0/1... Done.

Configuring Ten-GigabitEthernet1/0/2... Done.

Related commands

port link-type

Use

port link-type

to configure the link type of a port.

Use

undo port link-type

to restore the default link type of a port.

Syntax

port link-type

{

access

hybrid

trunk

}

undo port link-type

Default

Each port is an access port.

Summary of Contents for photosmart 850









































































































































Search results

Summary of Contents for photosmart 850

Reviews:

Brands by name

Popular brands

HP photosmart 850, Command Reference Manual

Search results

Summary of Contents for photosmart 850

Reviews:

Brands by name

Popular brands