HP photosmart 850 Page 51 Command Reference Manual Download | Manualshive

Page: 51 / 136

background image

46

You cannot assign Layer 2 aggregate interfaces to a VLAN.

Examples

# Assign Ten-GigabitEthernet 1/0/1 through Ten-GigabitEthernet 1/0/3 to VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] port Ten-GigabitEthernet1/0/1 to Ten-GigabitEthernet1/0/3

Related commands

display vlan

port access vlan

Use

port access vlan

to assign an access port to the specified VLAN.

Use

undo port access vlan

to restore the default.

Syntax

port access vlan

vlan-id

undo

port

access vlan

Default

All access ports belong to VLAN 1.

Views

WLAN-ESS interface view, Ethernet interface view, port group view, Layer 2 aggregate interface view

Default command level

2: System level

Parameters

vlan-id

: Specifies a VLAN ID in the range of 1 to 4094. Make sure the VLAN specified by the VLAN ID

already exists.

Usage guidelines

The configuration made in Ethernet interface view or WLAN-ESS interface view applies only to the port.
The configuration made in port group view applies to all ports in the port group.
The configuration made in Layer 2 aggregate interface view applies to the aggregate interface and its

aggregation member ports.

•

If the system fails to apply the configuration to the aggregate interface, it stops applying the
configuration to aggregation member ports.

•

If the system fails to apply the configuration to an aggregation member port, it skips the port and

moves to the next member port.

Examples

# Assign WLAN-ESS 1 to VLAN 3.

<Sysname> system-view

[Sysname] vlan 3

[Sysname-vlan3] quit

[Sysname] interface WLAN-ESS 1

«
...
49
50
51
52
53
...
»

Summary of Contents for photosmart 850









































































































































Reviews:

No comments

Related manuals for photosmart 850

Brand: Hama Pages: 2

Brand: Yoko Technology Pages: 58

ThinkPad TransNote

Brand: IBM Pages: 150

Wireless Multimedia Presenter with Trackball

Brand: Targus Pages: 16

Brand: Olympus Pages: 172

CVP9328DNIR-AHD

Brand: Concept Pro Pages: 8

Brand: VistaQuest Pages: 18

Brand: BELL+HOWELL Pages: 3

Brand: V-TAC Pages: 57

PARK VIEW ULTRA

Brand: Xblitz Pages: 44

Brand: FLIR Pages: 2

Brand: Sungale Pages: 43

Brand: Casio Pages: 39

MEGA-IMAGE 84 D

Brand: YAKUMO Pages: 43

Brand: Alfa Network Pages: 2

Brand: Uniq Pages: 14

LUMIX DMC-GF8KGN

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands