HP photosmart 850 Page 108 Command Reference Manual Download

Page: 108 / 136

103

Management address OID : 0

Port VLAN ID(PVID): 1

Port and protocol VLAN ID(PPVID) : 0

Port and protocol VLAN supported : No

Port and protocol VLAN enabled : No

VLAN name of VLAN 1: VLAN 0001

Auto-negotiation supported : Yes

Auto-negotiation enabled : No

OperMau : speed(10000)/duplex(Full)

PoE supported: No

Link aggregation supported : Yes

Link aggregation enabled : Yes

Aggregation port ID : 5

Maximum frame Size: 4096

MED information

Media policy type : Unknown

Unknown Policy : Yes

VLAN tagged : No

Media policy VlanID : 0

Media policy L2 priority : 0

Media policy Dscp : 0

LLDP local-information of port 5[Ten-GigabitEthernet1/0/4]:

Port ID subtype : Interface name

Port ID : Ten-GigabitEthernet1/0/4

Port description : Ten-GigabitEthernet1/0/4 Interface

Management address type : ipv4

Management address : 192.168.100.132

Management address interface type : IfIndex

Management address interface ID : 8

Management address OID : 0

Port VLAN ID(PVID): 1

Port and protocol VLAN ID(PPVID) : 0

Port and protocol VLAN supported : No

Port and protocol VLAN enabled : No

VLAN name of VLAN 1: VLAN 0001

Summary of Contents for photosmart 850









































































































































Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands

HP photosmart 850, Command Reference Manual

Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands