HP photosmart 850 Page 7 Command Reference Manual Download

Page: 7 / 136

default

Use

default

to restore the default settings for an Ethernet interface.

Syntax

default

Views

Ethernet interface view

Default command level

2: System level

Usage guidelines

CAUTION:

The

default

command might interrupt ongoing network services. Make sure you are fully aware of the

impacts of this command when you use it in a live network.

This command might fail to restore the default settings for some commands for reasons such as command

dependencies and system restrictions. Use the

display this

command in interface view to identify these

commands, and then use their

undo

forms or follow the command reference to individually restore their

default settings. If your restoration attempt still fails, follow the error message instructions to resolve the
problem.

Examples

# Restore the default settings for interface Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] default

This command will restore the default settings. Continue? [Y/N]:y

description

Use

description

to change the description of the interface.

Use

undo description

to restore the default.

Syntax

description

text

undo

description

Default

The default description of an interface is the interface name plus

Interface

. For example,

Ten-GigabitEthernet1/0/1 Interface

Views

Ethernet interface view

Default command level

2: System level

Summary of Contents for photosmart 850









































































































































Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands

HP photosmart 850, Command Reference Manual

Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands