manualshive.com logo in svg

HP photosmart 850, Command Reference Manual, Page: 113 / 136

Share
Download
HP photosmart 850 Command Reference Manual Download Page 113

 

108 

Table 23

 

Command output 

Field Description

LLDP neighbor-information of port 1 

LLDP information received through port 1. 

Update time 

Time when LLDP information about a neighboring device was last 
updated. 

Chassis type 

Chassis ID representation: 

•

 

Chassis component

. 

•

 

Interface alias

. 

•

 

Port component

. 

•

 

MAC address

. 

•

 

Network address (ipv4)

. 

•

 

Interface name

. 

•

 

Locally assigned

—Indicates a locally-defined chassis type other 

than those listed above. 

Chassis ID 

ID that identifies the LLDP sending device, which can be a MAC 
address, a network address, an interface, or some other value, 

depending on the chassis type. 

Port ID type 

Port ID representation: 

•

 

Interface alias

. 

•

 

Port component

. 

•

 

MAC address

. 

•

 

Network address (ipv4)

. 

•

 

Interface name

. 

•

 

Agent circuit ID.

 

•

 

Locally assigned

—Indicates a locally-defined port ID type other 

than those listed above. 

Port ID 

Value of the port ID type. 

System name 

System name of the neighboring device. 

System description 

System description of the neighboring device. 

System capabilities supported 

Capabilities supported on the neighboring device: 

•

 

Repeater

—Signal repeating is supported. 

•

 

Bridge

—Switching is supported. 

•

 

Router

—Routing is supported. 

System capabilities enabled 

Capabilities enabled on the neighboring device: 

•

 

Repeater

—Signal repeating is enabled. 

•

 

Bridge

—Switching is enabled. 

•

 

Router

—Routing is enabled. 

Management address OID 

Management address object ID. 

Port and protocol VLAN ID(PPVID) 

Port protocol VLAN ID.  

Port and protocol VLAN supported 

Indicates whether protocol VLAN is supported on the port. 

Port and protocol VLAN enabled 

Indicates whether protocol VLAN is enabled on the port. 

VLAN name of VLAN 1 

Name of VLAN 1. 

Auto-negotiation supported 

Indicates whether auto-negotiation is supported on the port. 

Summary of Contents for photosmart 850









































































































































Reviews:

No comments