HP photosmart 850 Page 122 Command Reference Manual Download

Page: 122 / 136

117

Views

Layer 2 Ethernet interface view, port group view

Default command level

2: System level

Parameters

disable

: Specifies the disable mode, where CDP-compatible LLDP cannot receive or transmit CDP

packets.

txrx

: Specifies the TxRx mode, where CDP-compatible LLDP can send and receive CDP packets.

Usage guidelines

For your device to work with Cisco IP phones, you must perform the following tasks:

•

Enable CDP-compatible LLDP globally.

•

Configure CDP-compatible LLDP to operate in TxRx mode on the specified ports.

Examples

# Configure CDP-compatible LLDP to operate in TxRx mode on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] lldp compliance admin-status cdp txrx

Related commands

lldp compliance cdp

Use

lldp compliance cdp

to enable global CDP compatibility.

Use

undo lldp compliance cdp

to restore the default.

Syntax

lldp compliance cdp
undo lldp compliance cdp

Default

CDP compatibility is globally disabled.

Views

System view

Default command level

2: System level

Usage guidelines

Because the maximum TTL allowed by CDP is 255 seconds, the TTL configuration must be no more than

255 seconds for CDP-compatible LLDP to operate with Cisco IP phones. The TTL configuration is the

product of the TTL multiplier and the LLDP frame transmission interval.

Examples

# Enable LLDP to be compatible with CDP globally.

Summary of Contents for photosmart 850









































































































































Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands

HP photosmart 850, Command Reference Manual

Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands