HP photosmart 850 Page 20 Command Reference Manual Download

Page: 20 / 136

Default command level

2: System level

Parameters

interface-type

: Specifies an interface type.

interface-number

: Specifies an interface number.

Usage guidelines

Clear old statistics on the interface before collecting new traffic statistics for a specific period of time.

•

If no interface type is specified, this command clears statistics for all interfaces on the device.

•

If only the interface type is specified, this command clears statistics for all interfaces of the specified
type.

•

If both the interface type and number are specified, this command only clears statistics for the
specified interface.

Examples

# Clear the statistics of Ten-GigabitEthernet 1/0/1.

<Sysname> reset counters interface ten-gigabitethernet 1/0/1

shutdown

Use

shutdown

to shut down an Ethernet interface.

Use

undo

shutdown

to bring up an Ethernet interface.

Syntax

shutdown
undo shutdown

Default

Ethernet interfaces are up.

Views

Ethernet interface view, port group view

Default command level

2: System level

Usage guidelines

You might need to shut down and then bring up an Ethernet interface to activate configuration changes

such as speed or duplex mode changes.
Do not execute the

shutdown

command on the following interfaces:

•

The internal interface connecting the HP 11900/10500/7500 20G unified wired-WLAN module
and the switch.

•

The internal interface connecting the HP 830 series PoE+ unified wired-WLAN switch or the HP 870
unified wired-WLAN appliance and the switching engine.

Examples

# Shut down and then bring up Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

Summary of Contents for photosmart 850









































































































































Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands

HP photosmart 850, Command Reference Manual

Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands