HP photosmart 850 Page 47 Command Reference Manual Download

Page: 47 / 136

Related commands

display vlan

reset counters interface vlan-interface

Use

reset counters interface vlan-interface

to clear statistics on a VLAN interface.

Syntax

reset counters interface

vlan-interface

[

vlan-interface-id

]

Views

User view

Default command level

2: System level

Parameters

vlan-interface-id

: Specifies a VLAN interface number.

Usage guidelines

Use this command to clear the history statistics if you want to collect statistics within a period.
If the

vlan-interface-id

argument is not specified, this command clears statistics of all VLAN interfaces.

If the

vlan-interface-id

argument is specified, this command clears statistics of the specified VLAN

interface.

Examples

# Clear statistics on VLAN-interface 2.

<Sysname> reset counters interface vlan-interface 2

Related commands

display interface vlan-interface

shutdown

Use

shutdown

to manually shut down a VLAN interface.

Use

undo shutdown

to bring up a VLAN interface.

Syntax

shutdown
undo shutdown

Default

A VLAN interface is not manually shut down. The VLAN interface is up if one or more ports in the VLAN

is up, and goes down if all ports in the VLAN go down.

Views

VLAN interface view

Default command level

2: System level

Summary of Contents for photosmart 850









































































































































Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands

HP photosmart 850, Command Reference Manual

Search results

Summary of Contents for photosmart 850

Reviews:

Related manuals for photosmart 850

Brands by name

Popular brands