-- Configure internal spanning tree (IST) instance.
■
■
-- Configure internal spanning tree (IST) instance ports parameters ([ethernet]
PORT-LIST)
■
-- Set the internal port pathcost for the IST (default is 'auto').
■
-- Use dynamic method of selecting a value for the path cost.
■
< 1 to 200000000 > -- Set port's path cost to the fixed value.
■
< 1 to 16 > -- ID of the MST instance to configure.
■
-- Configure MST instance ports parameters ([ethernet] PORT-LIST)
■
-- Set the port pathcost for the instance (default is 'auto').
■
-- Use dynamic method of selecting a value for the path cost.
■
< 1 to 200000000 > -- Set port's path cost to the fixed value.
■
< 0 to 15 > -- Set the port priority for the instance (the value is in range of 0-240
divided into steps of 16 that are numbered from 0 to 15, default is step 8).
■
< 0 to 15 > -- Set the device priority for the MST instance (the value is in range of
0-61440 divided into steps of 4096 that are numbered from 0 to 15, default is step 8).
■
-- Configure VLANs for the MST instance.
■
-- VLAN(s) to add to or to remove from the MST instance
(VLAN-ID-RANGE)
■
[no] spanning-tree
-- Set spanning-tree protocol to operate either in 802.1D legacy
mode or in 802.1s native mode. 'spanning-tree legacy-mode' is the equivalent of executing:
spanning-tree legacy-path-cost spanning-tree force-version stp-compatible 'no spanning-tree
legacy-mode' is the equivalent of executing: no spanning-tree legacy-path-cost spanning-tree
force-version mstp-operation
■
[no] spanning-tree
-- Set 802.1D (legacy) or 802.1t (not legacy) default pathcost
values.
■
spanning-tree
< 1 to 40 > -- Set the max number of hops in a region before the MST
BPDU is discarded and the information held for a port is aged (default is 20).
■
spanning-tree
< 6 to 40 > -- Set maximum age of received STP information before
it is discarded.
■
spanning-tree
-- Manipulate pending MSTP configuration
■
-- Apply pending MSTP configuration (swaps active and pending configuratons).
■
-- Set the pending MST region configuration name (default is switch's MAC
address).
■
-- Specify the configuration name (maximum 32 characters). (ASCII-STR)
■
< 0 to 65535 > -- Set the pending MST region configuration revision number
(default is 0).
■
-- Change pending MST instance configuration.
■
< 1 to 16 > -- ID of the MST instance to configure.
■
-- Configure VLANs for the MST instance.
■
-- VLAN(s) to add to or to remove from the MST instance
(VLAN-ID-RANGE)
■
-- Copy active configuration to pending.
■
[no] spanning-tree
-- Configure the port-specific parameters of the spanning tree protocol
for individual ports ([ethernet] PORT-LIST)
■
-- Set the administrative edge port status.
■
-- Set the automatic edge port detection.
■
-- Stop a specific port or ports from transmitting BPDUs, receiving BPDUs, and
assume a continuous fowarding state.
■
-- Disable the specific port or ports if the port(s) receives STP BPDUs.
■
-- Set message transmission interval (in sec.) on the port.
■
-- Use the globally configured hello-time value.
■
< 1 to 10 > -- Set message transmission interval (in sec.) on the port.
639
©
2009 Hewlett-Packard Development Company, L.P.
spanning-tree
Command Line Interface Reference Guide
Summary of Contents for 6200YL
Page 2: ......
Page 16: ...Introduction 14 2009 Hewlett Packard Development Company L P ...
Page 22: ...Commands 20 2009 Hewlett Packard Development Company L P ...
Page 764: ......