HP 54 Basic Cutter User Manual Download

Page: 9 / 58

Warnings and cautions

The following symbols are used in this manual to ensure the proper use of the cutter and to prevent the cutter

from being damaged. Follow the instructions marked with these symbols.

WARNING!

Failure to follow the guidelines marked with this symbol could result in serious personal injury or

death.

CAUTION:

Failure to follow the guidelines marked with this symbol could result in minor personal injury or

damage to the cutter.

Warning labels

Label

Explanation

Hazardous moving part. Keep your fingers and other body parts

away from this area.

This label is located on the scan axis.

Fuse caution label. For continued protection against risk of fire,

replace the fuse only with one of the same rating.

Double pole/Neutral fusing

This label is located near the power inlet, at the rear.

Caution: Always leave the pinch rollers in the upper positions when

the cutter is not in use.

This label is located on the side of the scan axis.

NOTE:

The final label position and size may vary slightly, but should always be visible and close to the potential

risk area.

Main cutter components

The following views of the cutter illustrate its main components.

ENWW

Main cutter components

Summary of Contents for 54 Basic Cutter



























































Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands

HP 54 Basic Cutter, User Manual

Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands