HP 54 Basic Cutter User Manual Download Page 14

Page: 14 / 58

Useful links

Visit the HP Latex Knowledge Center at

http://www.hp.com/communities/HPLatex

, where you can find detailed

information about our HP Latex products and applications, and use the forum to discuss anything related to the

business.

Product documentation:

http://www.hp.com/go/latex115/manuals/

User training (quick guide) is already installed in your computer. To reinstall:

http://www.hp.com/go/latex300/

quickguide/

Videos about how to use the cutter:

http://www.hp.com/supportvideos/

http://www.youtube.com/

HPSupportAdvanced

For more complete training program, see

http://www.hp.com/go/latex300printandcut/training

and

http://www.hp.com/go/latex115printandcut/training

Information about software RIPs, applications, solutions, inks, and substrates:

http://www.hp.com/go/latex300/

solutions/

and

http://www.hp.com/go/latex115/solutions/

HP Support:

http://www.hp.com/go/latex115/support/

Registration and communication with HP:

http://www.hp.com/communities/HPLatex/

The Quick Response (QR) code images found in some parts of this guide provide links to additional video

explanations of particular topics.

When you need help

In most countries, support is provided by HP support partners (usually the company that sold you the product). If

this is not the case in your country, contact HP Support on the Web as shown above.

Help is also available to you by telephone. What to do before you call:

●

Review the relevant parts of this guide.

●

Review your software documentation, if relevant.

●

Please have the following information available:

–

The product you are using: the product number and serial number.

NOTE:

These numbers are on a label at the rear of the cutter.

–

If there is an error code on the front panel, note it down.

–

The RIP you are using, and its version number.

–

If relevant, the substrate you are using.

Chapter 2 Useful links

ENWW

Summary of Contents for 54 Basic Cutter



























































Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands

HP 54 Basic Cutter, User Manual

Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands