HP 54 Basic Cutter User Manual Download

Page: 41 / 58

TurboCut

TurboCut increases throughput by speeding up the drag movement but without raising the overall speed of the

cutter. The cutting time reduction is significant, especially when cutting small, detailed designs. However, some

thicker materials may not cut well with this feature turned on.

Press the TurboCut button, then use

to activate or deactivate TurboCut. Press

to confirm or

to cancel. TurboCut is activated by default.

Panels

There are four parameters in the Panels submenu:

●

Panels: This parameter switches panels on or off.

●

Panel size: This parameter determines the length of the panel.

●

Panel replot: This parameter determines whether the design is to be cut more than once, panel per panel.

Panel replot is used for substrates that are thick or difficult to cut. The value of this parameter is

disregarded if paneling is set to off. If this parameter is set to 0, the cutter cuts each panel once only. If it is

set to 1, the cutter cuts each panel twice.

●

Sort vectors: See below.

Sort vectors

Sorting vectors is a submenu of the Panels menu, but because of its importance it is explained separately. There

are three options in this menu:

●

Off: When vector sorting is set off, the cutter does no optimizing of the vectors. This is used when the

intelligence of the cutter driver is preferred.

●

Directional: If set to directional, the vectors are optimized for the cutting direction (substrate advance). This

is used when the cutting pressure has to be set relatively high (for example during cutting through).

●

Starting point: This option optimizes the starting point for closed curves. This is used when the users sees

that the curves do not close as they should.

Paneling is used for various different applications. Below are the typical settings for the two most common

applications:

●

Cutting through: This is explained in

Cut through on page 30

. Typical settings for the parameters are:

Panels: On; Panel size: 5–10 cm; Panel replot: Off; Vector sorting: Directional.

●

Tracking difficult substrates: Typical settings for the parameters are: Panels: On; Panel size: 3–10 cm; Panel

replot: On/Off, depending on the thickness of the substrate. Vector sorting: Directional/Off, depending on

the required knife pressure and the substrate backing.

Calibrations

ENWW

System setup

Summary of Contents for 54 Basic Cutter



























































Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands

HP 54 Basic Cutter, User Manual

Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands