HP 54 Basic Cutter User Manual Download

Page: 17 / 58

Loosen the knobs on the two substrate flanges. The following illustration shows a loosened flange (1) and

a tightened flange (2).

Insert a loosened flange into one end of the substrate roll and tighten the knob. Verify that the flange is

secure. Then do the same at the other side of the roll.

Place the flange-equipped roll on the substrate supply rollers. Set the flanges inside the groove of the

flange guide. The flange guides can be moved laterally on the roller.

If the flanges are not used (this is not recommended, because then tracking is not guaranteed), then make

sure that the roll is situated between the two flange guides.

Start feeding the substrate in from the rear of the machine. Pass the substrate underneath the pinch rollers

towards the front of the cutter.

Position the left substrate edge on the leftmost drive sleeve and check that the right substrate edge is

positioned over the long drive sleeve.

NOTE:

If you have the HP 54 Basic Cutter, load the substrate as shown in the table below.

ENWW

Summary of Contents for 54 Basic Cutter



























































Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands

HP 54 Basic Cutter, User Manual

Search results

Summary of Contents for 54 Basic Cutter

Reviews:

Related manuals for 54 Basic Cutter

Brands by name

Popular brands