HP 4200 - LaserJet B/W Laser Printer User Manual Download Page 18

Page: 18 / 142

Configuring the IP Address Manually

In Manual mode, the following is displayed:

Display

Action

Use the number buttons on the front panel of the appliance to enter the IP address.

Press

Use the number buttons on the front panel of the appliance to enter the subnet mask.

Press

Use the numbers on the front panel of the appliance to enter the default gateway.

Press

After a moment, the appliance will resume displaying normal operating messages if
the IP address entered is valid.

Configuring the IP Address Using DHCP

In DHCP mode, the following is displayed:

Display

Action

The "=" will appear in the display.

Press

twice to display this message.

Press

After a moment, the appliance will resume displaying normal operating messages.

Use the web interface to further configure the appliance. Refer back to the

Getting Started procedures

, or refer directly to

information about using the

web interface

to further configure the device.

Summary of Contents for 4200 - LaserJet B/W Laser Printer















































































































































Search results

Summary of Contents for 4200 - LaserJet B/W Laser Printer

Reviews:

Related manuals for 4200 - LaserJet B/W Laser Printer

Brands by name

Popular brands

HP 4200 - LaserJet B/W Laser Printer, User Manual

Search results

Summary of Contents for 4200 - LaserJet B/W Laser Printer

Reviews:

Related manuals for 4200 - LaserJet B/W Laser Printer

Brands by name

Popular brands