background image

11

off center. Although the hammers were set at the factory, it is possible for them to

get out of adjustment. For most clocks, it will not be necessary to adjust chime

hammers. There are different types of chimes, (rods and tubes), please find yours

below.

CHIME ROD 

hammer arms are made of brass and can be safely bent. If necessary,

adjust hammers so that they do not interfere with each other while moving or striking 

the chime rods. This is accomplished by bending the hammer arms slightly in the middle 

so that each hammer rests approximately 1/8” from each rod. (See figure 20). 

DO NOT

 

bend the chime rods. Chime volume cannot be adjusted on a chime rod movement.

CHIME TUBE

 hammer arms are made of spring steel; 

DO NOT 

bend the hammer arms.

The clarity of sound is determined by the distance between the hammer and the

chime tube. This is typically 1/16”. (See figure 21). However, this distance can be

adjusted by loosening or tightening the thumb screw attached to the hammer string. 

(See figure 22). 

Important

: If the tension is too strong or the string is too tight, it can 

cause the chime to stop during the chime process.

NOTE: The hammer tension screw is set at the factory, and is NOT adjustable.

WEIGHTS DO NOT DROP AT THE SAME LEVEL

When the automatic nighttime shutoff feature is selected, and on some models the

“silent” feature, the center weight will drop at a faster rate than the other weights.

CLOCK WILL NOT RUN

Although it is not recommended that you repair your own clock, you should check these 

items before contacting us, your dealer, or an Authorized Service Center. (See Service 

Information Section.) Do not attempt any adjustment you do not feel 

confident in making.

1. Has all the packing material been removed from the movement area?

2. Has the pendulum guide spring clip been removed from the back of the

  movement?

3. Did you try re-starting your clock? Being “in beat” is necessary for your clock to

  keep running.

4. Are the weights hanging in the correct location? Check each weight bottom for

  proper location.

5. Is the pendulum hitting the weights or chime rods? If so, check the level and

  stability of the clock.

6. Is the clock level?

7. Has a pulley come off the cable or chain off the sprocket?

8. Do the hands operate without interference? Do not let the hour hand hit the 

  second hand. If the second hand is rubbing the dial, pull it out slightly. If the hour 

hand is rubbing against the back of the minute hand, the hour hand should be pushed 

closer to the dial (put your thumb nails on the center portion of the hour hand and 

push).

9. Did you check the click spring on the back side of the moon dial?

10. Did you remove the styrofoam blocks before they became loose through normal

  operation? (typically occurs after eight (8) hours of run time)

11. Did you check the suspension spring? If it is damaged, it must be replaced.

  (See figure 23).

12. Is the verge pin properly located in the slots of the pendulum guide? If not,

  reposition the verge pin. (See figure 23).

13. It is possible that the styrofoam blocks located above the cable pulleys are binding 

the cable. Carefully remove the styrofoam blocks by lifting the blocks straight up until 

they clear the cable pulley. Then gently push them back through the cables. Do not 

use tools to remove the blocks. Do not permit the cable to overlap on the drum.

FIGURE 20

FIGURE 21

FIGURE 22

FIGURE 23

HAMMER

 ARM

CHIME

ROD

CHIME

HAMMER

CHIME

TUBE

HAMMER

STRING

HAMMER

TENSION

SCREW

CHIME

TUBE

THUMB 

SCREW

SUSPENSION

SPRING

PENDULUM

POST

THUMB 

SCREW

VERGE

VERGE

PIN

PENDULUM 

GUIDE

Summary of Contents for 610519









































Reviews: