manualshive.com logo in svg

Horizon Reverse Osmosis Seafari Versatile SFC-1400-2, Owner'S Manual

Share
Download
Horizon Reverse Osmosis Seafari Versatile SFC-1400-2 Owner'S Manual Download Page 84

HRO

Systems

 Horizon 

Seafari

 Self Contained and Modular Style

 

J.  ELECTRONIC SUBSYSTEM:& TROUBLESHOOTING GUIDE 

 

 

 

HRO Control Touchpad. 

 

Water Quality Indicator remains Red (Un-potable Water) for Extended Period. 

 

The R.O. Membrane Element is fouled or has been attacked by chemicals. 
 
The R.O. Membrane Element has a broken product water tube caused by a restriction in the Product 
Water Line. 
 
The R.O. Membrane Element Product Water O-Ring is worn, cut or pinched and requires replacement. 
 
The Salinity Probe may have debris on it and requires cleaning. 
 
The Salinity Meter may require calibration.  Check the actual salinity content of the product water with a 
portable TDS meter to determine if the R.O. Membrane Element is fouled. 

 

Booster Pump: 

 

If the Booster Pump fails to operate, follow these steps to isolate the problem. 

 

1.

 

Make sure the system is receiving proper power and the “POWER” LED is on. 

 
2.

 

Press “Booster Pump” switch to activate the motor.  Do not press any other switch. 

 
3.

 

Measure the AC voltage between terminals 1 and 3 (single phase) or 1, 3 and 5 (3 phase) on TB-
1 in the main power enclosure. 

 

Page I - 10 

Summary of Contents for Seafari Versatile SFC-1400-2



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands