Hoppecke Sun Powerpack Premium Operating Manual Download Page 6

Page: 6 / 54

Means of Representation

BA_sun_power_pack_LiOn_en_V1.05.docx

V1.05 (20/07/2017) 6140203036

Means of Representation

The following icons and signal words have been used in this operating and maintenance
manual:

DANGER!

Denotes an immediate hazard with a high level of risk that could lead to death or severe physical

injury if it is not prevented.

WARNING!

Denotes a potential hazard with a medium level of risk that could lead to death or severe physical

injury if it is not prevented.

CAUTION!

Denotes a hazard with a low level of risk that could lead to minor or medium degree of physical

injury if it is not prevented.

ATTENTION!

Denotes a hazard in which the product, other objects or the environment may get damaged if it is

not prevented.

Denotes first-aid measures.

Note:

Denotes instructions that are important for optimal utilisation of the product.

Summary of Contents for Sun Powerpack Premium























































Search results

Summary of Contents for Sun Powerpack Premium

Reviews:

Related manuals for Sun Powerpack Premium

Brands by name

Popular brands

Hoppecke Sun Powerpack Premium, Operating Manual

Search results

Summary of Contents for Sun Powerpack Premium

Reviews:

Related manuals for Sun Powerpack Premium

Brands by name

Popular brands