Hongqi E-HS9 Manual Download Page 68 | Manualshive

Page: 68 / 395

background image

2. Instrument cluster

66

Interior backlight brightness adjustment

The interior backlight brightness can be adjusted in the driving information display area of
the instrument cluster. (Refer to P.76)

WARINING

◼

When adjusting brightness

For  the  sake  of  the  safety,  adjust  the  brightness  of  the  backlight  when  the  vehicle  is
parked.  Distracted  driving  shall  not  occur  or  the  driving  safety  shall  not  be  affected
because  of  the  use  of  this  function.  Ignoring  road  and  traffic  conditions  can  lead  to
accidents.

«
...
66
67
68
69
70
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Brand: UnderCover Pages: 16

Green Motion Building

Brand: Eaton Pages: 12

Brand: Yakima Pages: 8

Brand: NavLinkz Pages: 4

Brand: Porsche Pages: 144

Brand: Toyota Pages: 56

Brand: BMW Pages: 21

Brand: Mopar Pages: 17

C-Max Energi 2014

Brand: Ford Pages: 10

Brand: iSimple Pages: 12

Brand: Toyota Pages: 204

Brand: Buick Pages: 394

Brand: APS Pages: 4

Brand: GEMINI TECHNOLOGY Pages: 9

Brand: Brodit Pages: 2

Brand: SMART Pages: 26

Brand: Jotto Desk Pages: 3

Brand: Racepak Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands