Hongqi E-HS9 Manual Download Page 59 | Manualshive

Page: 59 / 395

background image

1-2. Charging/discharging

57

S

a

fe

ty

p

re

c

a

u

tio

n

s

1

Timed charging

◼

Timed charging settings

Turn the power (ignition) switch to ON.

Enable the timed charging and set the time
in the charging settings of the multimedia
system.

The  timed  charging  switch  is  OFF  by
default.  There  will  be  an  interval  of  at
least  10  minutes  between  the  start  time
and end time.

Park the vehicle in an AC chargeable area, switch the gear to P, apply the EPB,
connect the AC charging device, and set the charging pile to start charging. After
doing all these, if there is no system fault in the vehicle and the charging
equipment, the vehicle will begin to do AC charging at the appointed time set by
the user.

◼

Timed charging display

When the time for timed charging is not
reached, the instrument will display the
scheduled charging information, and the
scheduled charging indicator

will be

illuminated.

When the time for timed charging is reached,
the instrument will display "Start charging -
AC charging" in turn.

STEP

«
...
57
58
59
60
61
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 2

Brand: Yakima Pages: 12

Brand: RAM Pages: 116

Brand: Subaru Pages: 99

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: RAM Pages: 496

Brand: EUFAB Pages: 12

Brand: MULTILIFT Pages: 62

Brand: Sanitas Pages: 36

Brand: Jaeger Pages: 11

Brand: Ford Pages: 52

Brand: Volvo Pages: 16

Brand: Butts of Bawtry Pages: 2

LineCast Auto FM

Brand: Belkin Pages: 15

Brand: Rover Pages: 285

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands