Hongqi E-HS9 Manual Download Page 30 | Manualshive

Page: 30 / 395

background image

1-1.Instructions for safety operation

28

Supplemental Restraint System (SRS) components

Front passenger airbag

Front passenger seat airbag

Second-row seat airbag*

Driver airbag

Airbag control unit

Curtain airbag

Driver's seat airbag

Airbag fault alarm lamp

The above are the main components of the Supplemental Restraint System (SRS).

In  the  event  of  some  serious  front  or  side  impact,  the  SRS  will  trigger  the  airbag  gas
generator.  The  chemical  reaction  in  the  inflator  makes  the  airbag  filled  with  non-toxic  gas
quickly,  so  as  to  avoid  injury  to  the  occupants  due  to  a  secondary  collision  with  internal
parts of the vehicle.

«
...
28
29
30
31
32
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: Hama Pages: 2

Brand: Daihatsu Pages: 485

Brand: Daihatsu Pages: 43

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

Brand: Ultra Start Pages: 8

Brand: Mazdaspeed Pages: 8

Brand: walser Pages: 24

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

JEEP GL ADIATOR JT TOPPER ROOF RACK

Brand: JCROffroad Pages: 7

IVH-9000-2R440Q

Brand: Vecow Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands