Hongqi E-HS9 Manual Download Page 363 | Manualshive

Page: 363 / 395

background image

8-2. Measures to be taken in case of emergency

In case of low 12 V battery

361

In c as e of l ow 12 V bat tery

If the battery power is low, you can take the following measures to start the power
system.

You can contact an authorized FAW Hongqi dealer or a professional repair store.

If you have a set of jumper cables (or auxiliary cables) and another vehicle with a 12 V
battery, you can jumper start your vehicle by following these steps:

Detach the positive cover of the 12 V battery.

Connect the jumper cables.

Connect the positive (+) terminal of the 12 V battery on your vehicle.

Connect the positive (+) terminal of the 12 V battery on another vehicle.

Connect the negative (-) terminal of the 12 V battery on another vehicle.

Connect the negative (-) terminal of the 12 V battery on your vehicle.

Start the engine of the other vehicle. Increase the engine speed slightly and
keep it for about 5 min to recharge the 12 V battery of your vehicle.

Keep the engine of the other vehicle running, and then turn the power (ignition)
switch of your vehicle to ON.

Once the vehicle has been successfully started, remove the jumper cables in
the exact reverse order of when they were connected.

Once the vehicle is started, please drive the vehicle to an authorized FAW Hongqi dealer for
inspection as soon as possible.

STEP

«
...
361
362
363
364
365
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

PERFECTVIEW CAM80AHD

Brand: Dometic Pages: 196

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brand: Phonocar Pages: 6

Brand: Pyle Pages: 4

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

MagicComfort MSH200

Brand: Waeco Pages: 108

Brand: Tusk Pages: 2

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: TrailFX Pages: 2

Jumpy Miltispace

Brand: CITROËN Pages: 164

Brand: Directed Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands