Hongqi E-HS9 Manual Download Page 303

Page: 303 / 395

6-4. Other in-car equipment

Ceiling handle

301

-c

Ceiling handl e
Ceiling handl e

The ceiling handle is located at the roof side
member of each door.

When sitting on the seat, the body can be
supported by the ceiling handle mounted
on the roof lining.

WARINING

◼

Ceiling handle

Do not use the ceiling handle when getting in or out of the vehicle or getting up from the
seat.

Notice

◼

Preventing damage to ceiling handle

Do not hang any heavy objects or apply heavy loads on the ceiling handle to prevent
damage to the ceiling handle.

Summary of Contents for E-HS9












































































































































































































































































































































































































Search results

Summary of Contents for E-HS9

Reviews:

Related manuals for E-HS9

Brands by name

Popular brands

Hongqi E-HS9, Manual

Search results

Summary of Contents for E-HS9

Reviews:

Related manuals for E-HS9

Brands by name

Popular brands