Hongqi E-HS9 Manual Download Page 243

Page: 243 / 395

5-2. Operating the multimedia system

241

ime
d

Parking near the destination

When approaching the destination, you can use the P icon to display a list of nearby parking
locations.

Use these buttons to navigate between parking locations.

Displays the name and address of the parking location.

Map displaying the parking location.

Settings

The following controls are available in Settings:

Tap to access additional options.

Toggle the switch to turn the selected setting on or off.

Summary of Contents for E-HS9












































































































































































































































































































































































































Search results

Summary of Contents for E-HS9

Reviews:

Related manuals for E-HS9

Brands by name

Popular brands

Hongqi E-HS9, Manual

Search results

Summary of Contents for E-HS9

Reviews:

Related manuals for E-HS9

Brands by name

Popular brands