Hongqi E-HS9 Manual Download Page 106 | Manualshive

Page: 106 / 395

background image

3-3. Adjusting the seat

104

WARINING

◼

Precautions for headrest

Please observe the following precautions regarding headrests, otherwise it may lead to
serious injury or even death.

⚫

Please use the headrest specially designed for each seat.

⚫

Be sure to adjust the headrest to a suitable position for use.

⚫

Do not drive the vehicle with the headrest removed. Whenever you drive the vehicle,
you should install the headrest and adjust it to the right position. Driving with the
headrest positioned too low or not installed is very dangerous. In the event of a
collision, the lack of head support may cause serious injury to the neck.

◼

Headrests can reduce the whiplash effect and mitigate the neck injury of the
occupants in case of rear impact.

«
...
104
105
106
107
108
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Brand: Davis Instruments Pages: 16

Brand: JASTEC Pages: 12

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Kia Pages: 10

Brand: ECS Electronics Pages: 16

DBALL2-HYUNDAI9

Brand: Xpresskit Pages: 13

2011 3500 Chassis Cab

Brand: RAM Pages: 92

Brand: Metra Electronics Pages: 8

Easy Air Auto Screen

Brand: Wagan Pages: 8

Brand: Pontiac Pages: 486

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands