Hongqi E-HS9 Manual Download Page 58 | Manualshive

Page: 58 / 395

background image

1-2. Charging/discharging

56

Charging limit settings

The default custom charging limit in the vehicle is 100%.

⚫

Move the slider on the charging setting interface of the multimedia system to set the
charging limit. The setting range is 50%-100%, and the setting interval is 5%.

⚫

When the charging capacity is greater than or equal to the charging limit set by the
user, the vehicle will stop charging and prompt "Charging completed”.

⚫

When the vehicle displays "Charging completed", if the user sets the charging limit >
current power again at this time, the charging gun shall be reconnected before
starting charging again.

Discharge limit settings

The default custom discharge limit in the vehicle is 20%.

⚫

Move the slider on the charging setting interface of the multimedia system to set the
discharge limit. The setting range is 5%-40%, and the setting interval is 5%.

⚫

After the vehicle starts to discharge, the multimedia system will calculate the
remaining discharge time and prompt "AC discharging" simultaneously.

⚫

When the remaining power reaches the discharge limit set by the user, the vehicle will
stop discharging, and the instrument cluster display will prompt "SOC value

＜

set

value, discharging cannot be activated".

«
...
56
57
58
59
60
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Brand: Daihatsu Pages: 485

Brand: Garmin Pages: 2

AUDI 4G HIGHEND

Brand: KAP Pages: 20

Brand: Mercedes-Benz Pages: 30

Brand: Oldsmobile Pages: 2

Brand: Tachosys Pages: 28

Brand: E&G Classics Pages: 2

Brand: Yakima Pages: 13

Brand: Ecco Pages: 24

Brand: Improved Racing Pages: 17

Brand: E&G Classics Pages: 4

Brand: Honda Pages: 124

Brand: Mercedes-Benz Pages: 296

Bluetooth Kit3 PLUS

Brand: N-Com Pages: 36

Brand: Prorack Pages: 15

Brand: Mont Blanc Pages: 2

Brand: Ford Pages: 585

T13 Outback Frontal Protection System

Brand: T.J.M. Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands